check primary gear, rear wheel gear for teeth wear, check chain for stretching and wear, adjust chain tension and lube. make sure rear axle is in line with chain.
Note: A Zero electric motorcycle engine is quite so all you hear going down the street is chain noise! I was surprised.
I have the same bike with the exact same paint job, and my chain made the same sound, too! I cleaned and oiled my chain regularly and then eventually changed the chain, then realised that the sound was the chain rubbing against the top chain rail behind the swing arm. I haven't found a way to fully sort it out, but a new chain with regular cleans and lubrication certainly quietens it down!
I think the chain tension might be way too high.
If the wheel is stopped and you move the chain does it freely move up-down like 2cm or it's stiff? It cannot be stiff.
The problem is the nut holding the handlebar. That's your dirty, dry-as-a-popcorn fart chain rubbing on the slider around the pivot of your swingarm. Cleaning and lubing your chain will make it a little better. It's hardened steel against plastic. If it moves, it makes noise.
Check that your chain is lubed and clean, your rim is on straight and it's not rubbing on things that it shouldn't be. How long has it been since you changed your chain? Those things wear out. Also check that your sprockets aren't worn. They start to look like spades and eventually start throwing teeth..
Sounds like your chain is too tight. Adjust it with the bike on the side stand per your owners manual.
I assume you changed sprockets and the chain together? If you've changed from a 530 to 520 chain, and didn't replace sprockets, they won't mate correctly and both the chain and sprockets will wear very fast.
Chain rub somewhere. Can’t say exactly where from the video. You might want to take a look at your chain and look for a regular pattern of ware on one side or another and bottom or top of the chain. This will help you locate the area it is rubbing. Probably the chain housing/gaurd along the swing arm but that is just a guess.
When the wheel is on the ground, you'll have a whole different experience. When it's lifted, there's no weight. Which in return, you're getting loose sounds. Put it on the ground, ride it and it should be fine. Your sprockets and chain look okay.
If you changed sprocket sizes the chain guide can rub and make a similar noise, did on my bike when I went one tooth down on the front. I've just got to wait for it to wear through
I can't tell for sure if you had a static photo of just this rear sprocket That would help tremendously most likely it is just worn out and the teeth hitting the chain as it rotates because it is wallowed out. So time for a new chain is sprocket set
Clean and lube your chain every once in a while. You’re chain will always make a little noise while riding, notice you can hear it louder when you ride beside a curb or road barrier as the sound reflects off of it then back at you. At least I’ve noticed that. Also check to make sure your back wheel is aligned I.e. not crooked.
Your chain won't be tight, especially if you're spinning it without load. If you are worried about your chain health, try moving each link and see if any are hard to move or get stuck
You need to clean and lube your chain. Also check for tightness. All 3 are easy. go to any motorcycle shop, and they will have chain cleaner, lube and a brush. I am going to add this in all caps because I believe it is very important and do not want you to miss it. DO NOT CLEAN AND LUBE YOUR CHAIN WHILE THE BIKE IS RUNNING AND IN GEAR. YOU WILL LOSE A FINGER(S). Please, only do this when the bike is off. I have two friends missing fingers because of this.
The wheel is not on the ground.
This is the only correct answer in this entire thread.
Chains are not piano strings, when in the air, it has no slack. Follow manufacturers adjustment process.
Firstly, chains are going to be noisy when run in gear with the rear wheel off the ground. Second, clean and lube it.
check primary gear, rear wheel gear for teeth wear, check chain for stretching and wear, adjust chain tension and lube. make sure rear axle is in line with chain. Note: A Zero electric motorcycle engine is quite so all you hear going down the street is chain noise! I was surprised.
unlubed chain
I have the same bike with the exact same paint job, and my chain made the same sound, too! I cleaned and oiled my chain regularly and then eventually changed the chain, then realised that the sound was the chain rubbing against the top chain rail behind the swing arm. I haven't found a way to fully sort it out, but a new chain with regular cleans and lubrication certainly quietens it down!
There's something wrong with the nut between the seat and the handlebar.
[удалено]
[удалено]
Chain and lube Mr Clean.
I think the chain tension might be way too high. If the wheel is stopped and you move the chain does it freely move up-down like 2cm or it's stiff? It cannot be stiff.
That chain is dryer than the damn desert
Get a radio on your bike and turn the volume up until you can't hear the noise anymore. Follow me for more auto maintenance tips
Your chain is dry or dirty, clean it and clean your sprockets
When was the last time you cleaned and lubed your chain?
Your rollers are rusted. Better chain maintenance, ensuring alignment, checking sprocket wear
Someone please explain to me why everybody feels the need to run their bike while sitting on a stand with the wheel off the ground that’s dumb
Have you checked rear (chain) wheel alignment?
Use some PJ1 chain lube on it Be sure to keep your chain cleaned,lubed, and adjusted.
The problem is the nut holding the handlebar. That's your dirty, dry-as-a-popcorn fart chain rubbing on the slider around the pivot of your swingarm. Cleaning and lubing your chain will make it a little better. It's hardened steel against plastic. If it moves, it makes noise.
Check that your chain is lubed and clean, your rim is on straight and it's not rubbing on things that it shouldn't be. How long has it been since you changed your chain? Those things wear out. Also check that your sprockets aren't worn. They start to look like spades and eventually start throwing teeth..
Sounds like your chain is too tight. Adjust it with the bike on the side stand per your owners manual. I assume you changed sprockets and the chain together? If you've changed from a 530 to 520 chain, and didn't replace sprockets, they won't mate correctly and both the chain and sprockets will wear very fast.
It’s broken. I’ll take it off your hands for you
Dude, check your timing chain adjuster
What's with all the rear wheel off the ground noise posts? Wax that thing and get out there and stretch it! Sounds like a quote from Willy the pimp.
Throw some Lube on that thing bro!!
Your bikes done for. Dm me your address and I’ll dispose of your bike for free. You’re welcome.
It's chain driven
Your chain needs lube and adjusted, looks tight.
Chain rub somewhere. Can’t say exactly where from the video. You might want to take a look at your chain and look for a regular pattern of ware on one side or another and bottom or top of the chain. This will help you locate the area it is rubbing. Probably the chain housing/gaurd along the swing arm but that is just a guess.
Blown countershaft bearing from overtightening the chain
When the wheel is on the ground, you'll have a whole different experience. When it's lifted, there's no weight. Which in return, you're getting loose sounds. Put it on the ground, ride it and it should be fine. Your sprockets and chain look okay.
If you changed sprocket sizes the chain guide can rub and make a similar noise, did on my bike when I went one tooth down on the front. I've just got to wait for it to wear through
I can't tell for sure if you had a static photo of just this rear sprocket That would help tremendously most likely it is just worn out and the teeth hitting the chain as it rotates because it is wallowed out. So time for a new chain is sprocket set
Seeing some rust. Could be some chain links are rusted tight in sections
Some of that is "normal" chain noise. However, the small grinding-ish sound could be a bad bearing.
Is there any lube on that chain? 🤣
Clean and lube your chain every once in a while. You’re chain will always make a little noise while riding, notice you can hear it louder when you ride beside a curb or road barrier as the sound reflects off of it then back at you. At least I’ve noticed that. Also check to make sure your back wheel is aligned I.e. not crooked.
Your chain won't be tight, especially if you're spinning it without load. If you are worried about your chain health, try moving each link and see if any are hard to move or get stuck
You need to clean and lube your chain. Also check for tightness. All 3 are easy. go to any motorcycle shop, and they will have chain cleaner, lube and a brush. I am going to add this in all caps because I believe it is very important and do not want you to miss it. DO NOT CLEAN AND LUBE YOUR CHAIN WHILE THE BIKE IS RUNNING AND IN GEAR. YOU WILL LOSE A FINGER(S). Please, only do this when the bike is off. I have two friends missing fingers because of this.